halui(1) Manual Page

pin for clearing most errors

current applied tool length offset for the A axis

current applied tool length offset for the B axis

current applied tool length offset for the C axis

current applied tool length offset for the U axis

current applied tool length offset for the V axis

current applied tool length offset for the W axis

current applied tool length offset for the X axis

current applied tool length offset for the Y axis

current applied tool length offset for the Z axis

Current tool diameter, or 0 if no tool is loaded.

current selected tool

status pin that tells us if brake is on

pin for deactivating the spindle brake

pin for activating the spindle brake

a rising edge on this pin decreases the current spindle speed by 100

a rising edge on this pin makes the spindle go forward

a rising edge on this pin increases the current spindle speed by 100

контакт состояния, показывающий, включен ли шпиндель

a rising edge on this pin makes the spindle go reverse

контакт состояния, показывающий, вращается ли шпиндель в обратном направлении

контакт состояния, говорящий, вращается ли шпиндель вперед

фронт сигнала на этом контакте запускает шпиндель

фронт сигнала на этом контакте останавливает шпиндель

When TRUE, modify spindle override when counts changes.

counts X scale = spindle override percentage

pin for decreasing the SO (-=scale)

pin to enable direct spindle override value input

pin for increasing the SO (+=scale)

pin for resetting the scale SO value (scale=1.0)

pin for setting the scale of counts for SO

current FO value

status pin telling that block delete is on

pin for requesting that block delete is off

pin for requesting that block delete is on

status pin telling that no program is running

status pin telling that a program is paused

status pin telling that a program is running

status pin telling that the optional stop is on

pin requesting that the optional stop is off

pin requesting that the optional stop is on

pin for pausing a program

pin for resuming a program

pin for running a program

pin for stepping in a program

pin for stopping a program (note: this pin does the same thing as halui.abort)

pin for requesting auto mode

pin for auto mode is on

pin showing joint by joint jog mode is on

pin for manual mode is on

pin for MDI mode is on

pin showing coordinated jog mode is on

pin for requesting joint by joint jog mode

pin for requesting manual mode

pin for requesting MDI mode

pin for requesting coordinated jog mode

halui looks for INI variables named [HALUI]MDI_COMMAND, and exports a pin for each command it finds. When the pin is driven TRUE, halui runs the specified MDI command. XX is a two digit number starting at 00. If no [HALUI]MDI_COMMAND variables are set in the INI file, no halui.mdi-command-XX pins will be exported by halui.

pin for mist is on

pin for stopping mist

pin for starting mist

When True, modify max velocity when halui.max-velocity.counts changes.

When .count-enable is True, halui changes the max velocity in response to changes to this pin. It’s usually connected to an MPG encoder on an operator’s panel or jog pendant. When .count-enable is False, halui ignores this pin.

When this pin is True, halui commands the max velocity directly to (.counts * .scale). When this pin is False, halui commands the max velocity in a relative way: change max velocity by an amount equal to (change in .counts * .scale).

A positive edge (a False to True transition) on this pin increases the max velocity by the value of the .scale pin. (Note that halui always responds to this pin, independent of the .count-enable pin.)

A positive edge (a False to True transition) on this pin decreases the max velocity by the value of the .scale pin. (Note that halui always responds to this pin, independent of the .count-enable pin.)

This pin controls the scale of changes to the max velocity. Each unit change in .counts, and each positive edge on .increase and .decrease, changes the max velocity by .scale. The units of the .scale pin are machine-units per second.

Current value for maximum velocity, in machine-units per second.

контакт для единиц станка на мм (дюйм:1/25,4, мм:1) в соответствии с настройками файла INI: [TRAJ] LINEAR_UNITS

pin for machine is On/Off

pin for setting machine Off

pin for setting machine On

pin for selecting joint N

status pin that joint N is selected

status pin telling that joint N has a fault

pin for homing joint N

status pin telling that joint N is homed

status pin telling that joint N is on the positive hardware limit

status pin telling that joint N is on the negative hardware limit

status pin telling that joint N is on the positive software limit

status pin telling that joint N is on the negative software limit

контакт статуса , сообщающий, что пределы сочленения N временно переназначены

pin for unhoming joint N

selected joint number (0 …​ num_joints-1)

status pin selected joint is faulted

pin for homing the selected joint

status pin telling that the selected joint is homed

status pin telling that the selected joint is on the positive hardware limit

status pin telling that the selected joint is on the negative hardware limit

status pin telling that the selected joint is on the positive software limit

status pin telling that the selected joint is on the negative software limit

status pin telling that the selected joint’s limits are temporarily overridden

pin for unhoming the selected joint

контакт для установки зоны нечувствительности аналогового сигнала медленной подачи (аналоговые входы сигнала медленной подачи, меньше/медленнее этого (по абсолютному значению), игнорируются).

pin for setting jog speed for plus/minus jogging.

pin for jogging the joint N using a real value (e.g. joystick). The value, typically set between 0.0 and ±1.0, is used as a jog-speed multiplier.

контакт для установки инкремента шага для сочленения N при использовании приращения плюс/минус

фронт заставит сочленение N двигаться в отрицательном направлении на величину приращения

фронт заставит сочленение N двигаться в положительном направлении на величину приращения

контакт для медленной подачи сочленения N в отрицательном направлении со скоростью halui.joint.jog-speed

контакт для медленной подачи сочленения N в положительном направлении со скоростью halui.joint.jog-speed

pin for setting the jog increment for the selected joint when using increment-plus/minus

a rising edge will will make the selected joint jog in the negative direction by the increment amount

a rising edge will will make the selected joint jog in the positive direction by the increment amount

pin for jogging the selected joint in negative direction at the halui.joint.jog-speed velocity

pin for jogging the selected joint bit in in positive direction at the halui.joint.jog-speed velocity

pin for selecting axis by letter

контакт статуса , что ось L выбрана

Commanded axis position in machine coordinates

Feedback axis position in machine coordinates

Commanded axis position in relative coordinates

pin for setting jog analog deadband (jog analog inputs smaller/slower than this (in absolute value) are ignored)

pin for setting jog speed for plus/minus jogging.

pin for jogging the axis L using a real value (e.g. joystick). The value, typically set between 0.0 and ±1.0, is used as a jog-speed multiplier.

pin for setting the jog increment for axis L when using increment-plus/minus

по фронту ось L будет медленно подаваться в отрицательном направлении на величину приращения

по фронту будет осуществляться медленная подача оси L в положительном направлении на величину приращения

контакт для медленной подачи оси L в отрицательном направлении со скоростью halui.axis.jog-speed

контакт для медленной подачи оси L в положительном направлении со скоростью halui.axis.jog-speed

selected axis (by index: 0:x 1:y 2:z 3:a 4:b 5:cr 6:u 7:v 8:w)

pin for setting the jog increment for the selected axis when using increment-plus/minus

a rising edge will will make the selected axis jog in the negative direction by the increment amount

a rising edge will will make the selected axis jog in the positive direction by the increment amount

pin for jogging the selected axis in negative direction at the halui.axis.jog-speed velocity

pin for jogging the selected axis bit in in positive direction at the halui.axis.jog-speed velocity

pin for flood is on

pin for stopping flood

pin for starting flood

When TRUE, modify feed override when counts changes.

counts X scale = feed override percentage

pin for decreasing the FO (-=scale)

pin to enable direct value feed override input

pin for increasing the FO (+=scale)

pin for resetting the FO (scale=1.0)

pin for setting the scale on changing the FO

current feed override value

When TRUE, modify rapid override when counts changes.

counts X scale = rapid override percentage

pin for decreasing the rapid override (-=scale)

pin to enable direct value rapid override input

pin for increasing the rapid override (+=scale)

pin for resetting the rapid override (scale=1.0)

pin for setting the scale on changing the rapid override

current rapid override value

pin for setting E-stop (LinuxCNC internal) On

pin for displaying E-stop state (LinuxCNC internal) On/Off

pin for resetting E-stop (LinuxCNC internal) Off

pin for requesting home-all (only available when a valid homing sequence is specified)