NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Using LinuxCNC G Code Canned cycles relative - G91 G81 doing two times

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?
  • Page:
  • 1

TOPIC: Canned cycles relative - G91 G81 doing two times

Canned cycles relative - G91 G81 doing two times 29 Июл 2012 11:09 #22592

I'm using linuxcnc2.5 with Axis. I read a lot but I'm still a very beginner.
When I tried to make relative caned cycles I do not really understand the result.
I make the same call 2 times a get 2 different results.

The gcode is:

G90 g80 G0 Z1 (coordinate home)
X0 Y0 f1000
g91 G98 G81 X5 Y0 Z-5 R3 L3
g91 G98 G81 X5 Y0 Z-5 R3 L3
G90 g80 G0 Z1
X0 Y0
M2 (program end)

With the first time of calling g81 I have a kind of triangle trajectory.
The second (and any other) call(s) the move is (from my sight) as it should be.

1. So what I'm doing wrong?
2. When I change G98 to G99 see no change of the trajectory
The administrator has disabled public write access.

Re:Canned cycles relative - G91 G81 doing two times 30 Июл 2012 03:54 #22602

  • Rick G
  • Rick G's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1069
  • Thank you received: 15
  • Karma: 80
Not sure why you would have

g91 G98 G81 X5 Y0 Z-5 R3 L3
g91 G98 G81 X5 Y0 Z-5 R3 L3

together, but I would recomend a G80 after each canned cycle.

www.linuxcnc.org/docs/html/gcode/gcode.h...c_g80_cancel_modal_a

Rick G
The administrator has disabled public write access.

Re:Canned cycles relative - G91 G81 doing two times 30 Июл 2012 04:32 #22603

  • BigJohnT
  • BigJohnT's Avatar
  • NOW ONLINE
  • Administrator
  • Posts: 4950
  • Thank you received: 85
  • Karma: 134
It's a little difficult to understand but if you read the examples in the manual for G81 it should become clearer why your R value did not give you what you expected when using relative mode. The following code will give you what you expect. I assume but do not know as I don't see it specified in your example code that your using millimetres and not inches. It is a good idea to always put a preamble like shown in this G code tutorial.
G21 G17 G40 G49 G64 P0.005 G80 G90 G94
G0 Z1
X0 Y0
G91 G98 F1000
G81 X5 Y0 Z-5 R-1 L3
X5 Y0 L3
G80
M2

John
The administrator has disabled public write access.

Re:Canned cycles relative - G91 G81 doing two times 30 Июл 2012 10:50 #22610

True. Exactly that was I intend to do. I will read the manual once more.
Thanks
Juergen
The administrator has disabled public write access.

Re:Canned cycles relative - G91 G81 doing two times 30 Июл 2012 10:56 #22611

  • BigJohnT
  • BigJohnT's Avatar
  • NOW ONLINE
  • Administrator
  • Posts: 4950
  • Thank you received: 85
  • Karma: 134
BTW, the screen shot was a nice addition to your original post as it made it much easier to understand your problem exactly.

John
The administrator has disabled public write access.
  • Page:
  • 1
Time to create page: 1.183 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.