NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Configuring LinuxCNC ClassicLadder paragraph settings config

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?
  • Page:
  • 1
  • 2

TOPIC: paragraph settings config

paragraph settings config 24 Mag 2012 05:40 #20325

  • chime
  • chime's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 6
  • Karma: 0
good afternoon everyone, I am trying to do little things at the classicladder, and I looked at the manual, one thing that I find how to do to be able to extend network range of addresses with their respective inputs or outputs
How I can insert another page modbus i / o setup register?
Greetings to all and have if someone can guide me
The administrator has disabled public write access.

Re:paragraph settings config 24 Mag 2012 18:22 #20359

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1486
  • Thank you received: 40
  • Karma: 89
please explain 'extend network range of address'

you need more then 15 entries?
The administrator has disabled public write access.

Re:paragraph settings config 25 Mag 2012 04:39 #20384

  • chime
  • chime's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 6
  • Karma: 0
Good, thanks for answering,


if I need to extend the range of addresses off with more than 15 as I can place another page address? I never looked manuals and the wiki but i can not find anything about it, can guide me?
thanks
Albet
The administrator has disabled public write access.

Re:paragraph settings config 09 Ago 2012 10:46 #23002

  • chime
  • chime's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 6
  • Karma: 0
hello good, I'm trying to find somewhere but can not find information on how to expand the address records, you may not be? could someone help me where to start.


regards
Albert
The administrator has disabled public write access.

Re:paragraph settings config 09 Ago 2012 12:43 #23003

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 4940
  • Thank you received: 84
  • Karma: 133
If you mean how do I increase the number of variables in classicladder... it is in the Classicladder section of the Integrators manual.

John
The administrator has disabled public write access.

Re:paragraph settings config 09 Ago 2012 13:52 #23006

  • chime
  • chime's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 6
  • Karma: 0
hi john


integrator manual and looked at me, but that variable is the page which raises the modbus i / o setup register?




regards
Albert
The administrator has disabled public write access.

Re:paragraph settings config 09 Ago 2012 13:58 #23007

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 4940
  • Thank you received: 84
  • Karma: 133
I'm not familiar with the modbus part of classicladder other that what is in the manual.

John
The administrator has disabled public write access.

Re:paragraph settings config 12 Ago 2012 03:18 #23073

  • chime
  • chime's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 6
  • Karma: 0
hi john

Thanks for responding, I will continue looking for information to have if I can get.


regards
Albert
The administrator has disabled public write access.

Re:paragraph settings config 12 Ago 2012 10:35 #23076

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1486
  • Thank you received: 40
  • Karma: 89
15 entries is all classicladder has.
not that it couldn't have more but would need to be editted and recompiled.
Why do you need so many?
The administrator has disabled public write access.

Re:paragraph settings config 12 Ago 2012 11:13 #23077

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1486
  • Thank you received: 40
  • Karma: 89
What version of linuxcnc are you using?
your pic is not from 2.5 ....
The administrator has disabled public write access.
  • Page:
  • 1
  • 2
Time to create page: 0.812 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.