NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Configuring LinuxCNC GladeVCP How to integrate gladeVCP?

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?
  • Page:
  • 1

TOPIC: How to integrate gladeVCP?

How to integrate gladeVCP? 26 Jun 2012 01:00 #21335

  • Revilo
  • Revilo's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 7
  • Karma: 0
Hey Hey,

it might be a stupid question for you but i am a bloody rookie in the whole story. never worked with linux, no experience in programming.
however my mill works....partially:)

my question now is: in the integrators manual they say:

Run the same panel as a tab inside Axis as follows:

$ cd configs/sim/gladevcp
$ linuxcnc gladevcp_tab.ini

where do i have to write these commands in?
i read something about git?what is it?


greetz
The administrator has disabled public write access.

Re:How to integrate gladeVCP? 26 Jun 2012 03:58 #21351

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 4940
  • Thank you received: 84
  • Karma: 133
Usually when you see the dollar sign it means things you typed into the terminal window. And indeed those are terminal commands. For more info on that read here.

Unless you require a more complex Virtual Control Panel I would suggest starting with Python VCP it is a much simpler interface to add and use.

John
The administrator has disabled public write access.

Re:How to integrate gladeVCP? 27 Jun 2012 08:48 #21392

  • andypugh
  • andypugh's Avatar
  • NOW ONLINE
  • Moderator
  • Posts: 4090
  • Thank you received: 139
  • Karma: 129
Revilo wrote:
Run the same panel as a tab inside Axis as follows:

$ cd configs/sim/gladevcp
$ linuxcnc gladevcp_tab.ini

where do i have to write these commands in?

In a terminal window. However I am not sure why the instructions say to do it that way, as it is equivalent to selecting LinuxCNC from the application menu, then selecting the sim/gladevcp configuration.
The administrator has disabled public write access.

Re:How to integrate gladeVCP? 27 Jun 2012 13:11 #21414

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 4940
  • Thank you received: 84
  • Karma: 133
andypugh wrote:
Revilo wrote:
Run the same panel as a tab inside Axis as follows:

$ cd configs/sim/gladevcp
$ linuxcnc gladevcp_tab.ini

where do i have to write these commands in?

In a terminal window. However I am not sure why the instructions say to do it that way, as it is equivalent to selecting LinuxCNC from the application menu, then selecting the sim/gladevcp configuration.

That is left over from when you could only get 2.5 as a git RIP.

John
The administrator has disabled public write access.
  • Page:
  • 1
Moderators: mhaberler
Time to create page: 0.887 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.