NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Configuring LinuxCNC PnCConf Wizard pncconf - feature requests

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?

TOPIC: pncconf - feature requests

Re:pncconf - feature requests 31 Mär 2011 15:50 #8350

  • Zig
  • Zig's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 139
  • Karma: 1
Chris,

attached the current configuration of the machine.

No spindle control. I need to think through the safety interlocks as the spindle has a pneumatic collet. I have to investigate the spindle speed monitor and interlock the air solenoid ( which is presently push button activated ) so that an auto tool changer functionality can be implemented.

So a basic XYZ METRIC machine.
Leadscrews are 5 mm pitch.
Servo motors are directly coupled to the screws.
Linear scale has a basic resolution of 20 micron but in quadrature mode the resolution is 5 micron.
The reader head on the scale outputs an Index pulse for homing as well as an end of travel flag ( a single flag for both positive and negative limits).

This attachment is hidden for guests. Please log in or register to see it.
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
Last Edit: 31 Mär 2011 15:50 by Zig.
The administrator has disabled public write access.

Re:pncconf - feature requests 31 Mär 2011 15:52 #8351

  • Zig
  • Zig's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 139
  • Karma: 1
Config file

This attachment is hidden for guests. Please log in or register to see it.
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
Last Edit: 31 Mär 2011 15:52 by Zig.
The administrator has disabled public write access.

Re:pncconf - feature requests 31 Mär 2011 15:54 #8352

  • Zig
  • Zig's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 139
  • Karma: 1
and the third part of the trilogy ( thank goodnes its not in four parts)

This attachment is hidden for guests. Please log in or register to see it.


Sorry about this
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
The administrator has disabled public write access.

Re:pncconf - feature requests 31 Mär 2011 16:01 #8353

  • Zig
  • Zig's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 139
  • Karma: 1
and the planned interface electronics


EDIT..file too large
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
Last Edit: 31 Mär 2011 16:46 by Zig.
The administrator has disabled public write access.

Re:pncconf - feature requests 31 Mär 2011 16:54 #8359

  • Zig
  • Zig's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 139
  • Karma: 1
Ok smaller size file...



This attachment is hidden for guests. Please log in or register to see it.
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
The administrator has disabled public write access.

Re:pncconf - feature requests 31 Mär 2011 17:47 #8361

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1489
  • Thank you received: 40
  • Karma: 89
couldn't load this last one...
The administrator has disabled public write access.

Re:pncconf - feature requests 31 Mär 2011 18:35 #8362

  • Zig
  • Zig's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 139
  • Karma: 1
Chris,

Apologies...

The file was compressed into a RAR format and relabeled as .ZIP to comply with the file extension filter.

This is a more complete drawing

EDIT: still too large
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
Last Edit: 31 Mär 2011 18:39 by Zig.
The administrator has disabled public write access.

Re:pncconf - feature requests 31 Mär 2011 18:45 #8363

  • Zig
  • Zig's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 139
  • Karma: 1
Updated schematic diagram ( atium DXp 2004 version available) This attachment is hidden for guests. Please log in or register to see it.


EDIT:

Ought we move this to a separatetopic?
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
Last Edit: 31 Mär 2011 18:49 by Zig.
The administrator has disabled public write access.

Re:pncconf - feature requests 01 Apr 2011 19:18 #8379

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1489
  • Thank you received: 40
  • Karma: 89
ya we prob should... I have most of a config built. I don't use mm often ans so a few bugs showed up..working through them
The administrator has disabled public write access.

Re:pncconf - feature requests 09 Mai 2011 10:37 #9681

  • fabworx
  • fabworx's Avatar
  • OFFLINE
  • Senior Boarder
  • Posts: 64
  • Karma: 1
how about a actuall map out of the physical pins on which daughter board to be connected. as in ok my spindle pmw that i configured in the mesa tabs will be say pin 1, and 2 on the 7i48 p2 connector. does that make sence
The administrator has disabled public write access.
Moderators: cmorley
Time to create page: 1.486 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.