NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Configuring LinuxCNC PnCConf Wizard 7i43 and 7i48

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?

TOPIC: 7i43 and 7i48

Re:7i43 and 7i48 12 Oct 2011 22:24 #13884

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1489
  • Thank you received: 40
  • Karma: 89
Then you compiled it your self? Does the splash page in pncconf say alpha or beta1? (this is on the page it's self not in the terminal.
The administrator has disabled public write access.

Re:7i43 and 7i48 12 Oct 2011 22:57 #13885

  • ericson
  • ericson's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 13
  • Karma: 0
I'll check it out when I get home
in a few hours
The administrator has disabled public write access.

Re:7i43 and 7i48 13 Oct 2011 10:58 #13894

  • ericson
  • ericson's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 13
  • Karma: 0
finally it works
I had the beta1 version.
thank you for your help
The administrator has disabled public write access.

Re:7i43 and 7i48 13 Oct 2011 17:16 #13899

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1489
  • Thank you received: 40
  • Karma: 89
beta1 is good.
Hope it helps you out.
Let me know of any other problems.
The administrator has disabled public write access.

Re:7i43 and 7i48 16 Fév 2012 15:05 #17735

  • PKM
  • PKM's Avatar
  • OFFLINE
  • Senior Boarder
  • Posts: 50
  • Thank you received: 1
  • Karma: 4
Hello!
I have the same hardware
BIT and PIN files copied to /lib/firmware/hm2/7i43-4
when starting Pncconf (beta 1 on compiled linuxcnc 2.6.0) I have

/home/pkm/Desktop/custom_firmware/firmware.py
**** PNCCONF ERROR: custom firmware loading error

Where should I look?
The administrator has disabled public write access.

Re:7i43 and 7i48 16 Fév 2012 19:14 #17747

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1489
  • Thank you received: 40
  • Karma: 89
pncconf has changed since then.

delete the custom_firmware folder from the desktop.
post your PIN file here and I will make a XML file for you.
The XML file goes were the BIT file went.
The administrator has disabled public write access.
Moderators: cmorley
Time to create page: 1.051 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.