NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum General General LinuxCNC Questions Swits problems

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?

TOPIC: Swits problems

Re:Swits problems 08 Jui 2012 03:11 #20742

  • cncbasher
  • cncbasher's Avatar
  • OFFLINE
  • Moderator
  • Posts: 686
  • Thank you received: 30
  • Karma: 53
please post your hal file and ini file from your config folder ..
also list your parrell port pin assignment

i presume you are using stepconf to assign pins .
joint 0 on limit switch error is , the joint 0 limit switch is active ( could be the pin needs to be inverted ) depending if your switches are normaly closed rather than normaly open
this can be checked in AXIS using the hal configuration windows ( under the machine tab )

joint 0 = X joint 1 = Y etc....

home switch location values are stored in the ini file. and can be hand edited usiing gedit for example
parrell port setup is in the HAL file and again can also be hand edited ..
The administrator has disabled public write access.

Re:Swits problems 08 Jui 2012 04:12 #20744

  • Frederik
  • Frederik's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 19
  • Karma: 0
here is some files This attachment is hidden for guests. Please log in or register to see it.
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
The administrator has disabled public write access.

Re:Swits problems 08 Jui 2012 04:23 #20745

  • Frederik
  • Frederik's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 19
  • Karma: 0
ini file This attachment is hidden for guests. Please log in or register to see it.
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
The administrator has disabled public write access.

Re:Swits problems 08 Jui 2012 04:24 #20746

  • Frederik
  • Frederik's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 19
  • Karma: 0
Hal file This attachment is hidden for guests. Please log in or register to see it.
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
The administrator has disabled public write access.

Re:Swits problems 08 Jui 2012 05:27 #20747

  • cncbasher
  • cncbasher's Avatar
  • OFFLINE
  • Moderator
  • Posts: 686
  • Thank you received: 30
  • Karma: 53
are you able to see the switch changing state in the hal configuration ?
you do seem to have the pin selected correctly
so selecting within hal configuration .,.. pins ... and then parport select the watch window and the pin for example pin-11-in-not . if you then toggle the switch manualy the watch pin should change state

are your switches connected to ground and the port pin ?
Last Edit: 08 Jui 2012 05:38 by cncbasher.
The administrator has disabled public write access.

Re:Swits problems 08 Jui 2012 06:21 #20748

  • Frederik
  • Frederik's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 19
  • Karma: 0
I have checked everything, but is is no forbinfelse to the software when I activate switches ... Who is as for missing a checkbox somewhere.
But now I have set x to 0 and Y to 0, so I have to manually run indtilvidere.
But if you find solution later I would be super happy. A thousand thanks for now and good weekend/Frederick
The administrator has disabled public write access.
Time to create page: 0.897 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.