NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Using LinuxCNC G Code Need to turn 90 degs.

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?

TOPIC: Need to turn 90 degs.

Re:Need to turn 90 degs. 19 Jan 2012 14:47 #16959

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 5075
  • Thank you received: 101
  • Karma: 135
Unfortunately the docs are correct but confusing to read... the correction is on the list, thanks for finding the confusion. And my mistake in linking 2.5 docs which support P0 for the current coordinate system. I guess I'm excited about 2.5 fixing to hit the streets and tend to wander over to those docs...

2.4.x docs are here:

linuxcnc.org/docview/html/gcode_main.htm...:G10:-Set-Coordinate

John
The administrator has disabled public write access.

Re:Need to turn 90 degs. 19 Jan 2012 15:10 #16961

  • cwebs
  • cwebs's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 123
  • Karma: 5
Ok. I tried P1 and got no error using Mach3 Sim. But The work peice was not turned 90 degz. I will try in in LinuxCNC tonight. THanks John.
I knew you made that boo boo but was saving your feelings. Carl
The administrator has disabled public write access.

Re:Need to turn 90 degs. 19 Jan 2012 15:14 #16962

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 5075
  • Thank you received: 101
  • Karma: 135
Well the mack sim will be different for sure...

John
The administrator has disabled public write access.

Re:Need to turn 90 degs. 19 Jan 2012 15:15 #16963

  • andypugh
  • andypugh's Avatar
  • OFFLINE
  • Moderator
  • Posts: 4243
  • Thank you received: 152
  • Karma: 130
cwebs wrote:
Ok. I tried P1 and got no error using Mach3 Sim. But The work peice was not turned 90 degz.
You might not see it. I only saw it in the EMC2 sim because the right-arrow started moving the Y axis on-screen
I should have remembered to try 45 degrees, then all arrow keys ought to move both axes…
The administrator has disabled public write access.

Re:Need to turn 90 degs.(Solved) 19 Jan 2012 15:26 #16964

  • cwebs
  • cwebs's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 123
  • Karma: 5
THe P1 did the trick. It doesn't work in Mach3 Sim but you were right Andy it does work just fine in LinuxCNC. You see John, I knew if you read the man you would be able to do it! Thanks guys, Carl
The administrator has disabled public write access.

Re:Need to turn 90 degs.(Solved) 19 Jan 2012 16:18 #16966

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 5075
  • Thank you received: 101
  • Karma: 135
Well the statement about jogging is correct in the 2.5 docs :)

linuxcnc.org/docview/2.5/html/gcode/gcod...em_a_id_sec_g10_l2_a

John
The administrator has disabled public write access.
Time to create page: 1.394 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.