NEWS
LinuxCNC 2.5.2 Release
LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum General General LinuxCNC Questions Spindle joint Following error

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?
  • Page:
  • 1
  • 2

TOPIC: Spindle joint Following error

Spindle joint Following error 05 Jul 2012 08:30 #21612

  • SRT
  • SRT's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 141
  • Thank you received: 1
  • Karma: 1
I am retrofitting a Lathe with EMC. 30 Hp Reliance DC motor and spindle drive. My problem is following errors on the spindle joint......If I try to spin the axis by hand with EMC in the run state I get a following error and I attribute it to EMC seeing movement when there is none called out or requested. The second case is when I actually call for spindle movement I get a following error before the spindle gets up to speed. The spindle starts but the following error shuts everything off pretty fast. Any Ideas?
The administrator has disabled public write access.

Re:Spindle joint Following error 05 Jul 2012 08:35 #21613

  • PCW
  • PCW's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1668
  • Thank you received: 87
  • Karma: 116
The spindle is normally not a motion axis so following error should not even apply to spindle motion. Can you post yout HAL and INI files?
The administrator has disabled public write access.

Re:Spindle joint Following error 05 Jul 2012 08:42 #21614

  • SRT
  • SRT's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 141
  • Thank you received: 1
  • Karma: 1
I will try This attachment is hidden for guests. Please log in or register to see it.
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
The administrator has disabled public write access.

Re:Spindle joint Following error 05 Jul 2012 08:43 #21615

  • SRT
  • SRT's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 141
  • Thank you received: 1
  • Karma: 1
INI File This attachment is hidden for guests. Please log in or register to see it.
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
The administrator has disabled public write access.

Re:Spindle joint Following error 05 Jul 2012 08:46 #21616

  • SRT
  • SRT's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 141
  • Thank you received: 1
  • Karma: 1
I see I do have it as a motion axis. I do believe that was created through PNCconfig but it was so long ago that I have forgotten that part. I am starting to make major progress but the problems seem to be getting bigger....LOL

Thanks
The administrator has disabled public write access.

Re:Spindle joint Following error 05 Jul 2012 08:56 #21617

  • SRT
  • SRT's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 141
  • Thank you received: 1
  • Karma: 1
What are my choices of signals except the motion signals? should I be connected to the manual signals?
The administrator has disabled public write access.
  • Page:
  • 1
  • 2
Time to create page: 0.812 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.