NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Configuring LinuxCNC PnCConf Wizard Mesa 7I43-4 first tests but no sucess

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?

TOPIC: Mesa 7I43-4 first tests but no sucess

Re:hm2/7i43-Re:Mesa 7I43-4 first tests but no sucess 29 Июл 2012 09:46 #22589

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1520
  • Thank you received: 41
  • Karma: 89
also did the steppers move in PNCconf's tune test?
The administrator has disabled public write access.

Re:hm2/7i43-Re:Mesa 7I43-4 first tests but no sucess 29 Июл 2012 10:08 #22590

  • Mike_Eitel
  • Mike_Eitel's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 136
  • Thank you received: 2
  • Karma: 2
Hi

Oops, I forgot two explain:

I get E-stop and limit switches correctly.

Yes the macine is runnig in axis, showing usual moves... Usinf the LinuxCNC engraving.

It's on my test configuration, witch was always runnig fine with parports.
Same L297 boars with small steppers to see things moving.
Checked all with Fluke hand oscillopscope.

NO output signal seams to be driven... Maybe a watchdog-issue ?

to make a test I used pure pncconf ... so it should be fine.

Mike

AND
NO also in tune test they do not move!
Last Edit: 29 Июл 2012 10:08 by Mike_Eitel.
The administrator has disabled public write access.

Re:hm2/7i43-Re:Mesa 7I43-4 first tests but no sucess 29 Июл 2012 13:50 #22596

  • PCW
  • PCW's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1718
  • Thank you received: 92
  • Karma: 116
Does the built in hm2-stepper example config work? (as far as step and dir go)
The administrator has disabled public write access.

Re:hm2/7i43-Re:Mesa 7I43-4 first tests but no sucess 29 Июл 2012 14:33 #22598

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1520
  • Thank you received: 41
  • Karma: 89
you have edited the HAL file.
It mentions LEDs in the hostmot2 loading line - PNCconf does not configure LEDs
does the 7i43 have LEDS?
remove the num_leds=-1 from line 9 of the mesaCNC.hal file.
it is unnecessary anyways as -1 is the default

It shouldn't matter but lets start there...
The administrator has disabled public write access.

Re:hm2/7i43-Re:Mesa 7I43-4 first tests but no sucess 29 Июл 2012 14:56 #22599

  • PCW
  • PCW's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1718
  • Thank you received: 92
  • Karma: 116
The 7I43 has 8 user LEDs
The administrator has disabled public write access.

Re:hm2/7i43-Re:Mesa 7I43-4 first tests but no sucess 30 Июл 2012 08:31 #22609

  • Mike_Eitel
  • Mike_Eitel's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 136
  • Thank you received: 2
  • Karma: 2
Salu

Yes PCW, your idea was a good hint.

The simple demo runs fine...

Now I can do debugging myself why the other config doesn't like me. ;-()

THX
Mike
The administrator has disabled public write access.
Moderators: cmorley
Time to create page: 1.146 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.