NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Configuring LinuxCNC StepConf Wizard stepconf woes..

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?
Forum Header

TOPIC: stepconf woes..

Re:stepconf woes.. 15 Июн 2011 14:24 #10548

  • submicro
  • submicro's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 84
  • Karma: 1
I deleted all files in the Emc folder and all files on the desktop. I'll do it again just to be sure
The administrator has disabled public write access.

Re:stepconf woes.. 15 Июн 2011 14:25 #10549

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 4959
  • Thank you received: 87
  • Karma: 134
and the emc folder to just to be sure

John
The administrator has disabled public write access.

Re:stepconf woes.. 15 Июн 2011 14:35 #10550

  • submicro
  • submicro's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 84
  • Karma: 1
ok deleting the folder seemed to fix that problem. But I'm still were I was to begin with!
The administrator has disabled public write access.

Re:stepconf woes.. 15 Июн 2011 14:52 #10555

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 4959
  • Thank you received: 87
  • Karma: 134
So, recap where you are now. What is connected etc.

John
The administrator has disabled public write access.

Re:stepconf woes.. 15 Июн 2011 15:12 #10557

  • submicro
  • submicro's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 84
  • Karma: 1
oK...


As I said before pins 1-6 of the parallel port remain at a constant +5.26vdc, regardless of whether EMC is running or not. Nothing I do changes this and I mean NOTHING. Well unless I turn off the computer :-)
I'm not using the PCI card at thks time, decided to go back to the onboard port for awhile.
I have the cable connecting the c10 breakout board which is connected to the keling 4030's which are connected to the motors.
The administrator has disabled public write access.

Re:stepconf woes.. 15 Июн 2011 16:06 #10559

  • andypugh
  • andypugh's Avatar
  • NOW ONLINE
  • Moderator
  • Posts: 4138
  • Thank you received: 141
  • Karma: 130
submicro wrote:
As I said before pins 1-6 of the parallel port remain at a constant +5.26vdc, regardless of whether EMC is running or not. Nothing I do changes this

Do the other pins change? ie is it only 1-6 that are stuck? If so then I would suspect a hardware fault.

If the other pins don't work either, then I suspect you still haven't got the parport base address right.

What does dmesg say? What does cat /proc/ioports say?
The administrator has disabled public write access.
Time to create page: 1.695 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.