NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Configuring LinuxCNC PnCConf Wizard 7i64 & 7i70 - 7i44 - 5i23 support?

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?
  • Page:
  • 1
  • 2

TOPIC: 7i64 & 7i70 - 7i44 - 5i23 support?

Re:7i64 & 7i70 - 7i44 - 5i23 support? 06 Lug 2012 16:57 #21658

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1486
  • Thank you received: 40
  • Karma: 89
Did the 7i64 work out ?
The administrator has disabled public write access.

Re:7i64 & 7i70 - 7i44 - 5i23 support? 06 Lug 2012 17:09 #21661

  • clkeck1
  • clkeck1's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 91
  • Karma: 2
7i64 looks right

The file should be SVSS though not SSSV. it is putting it backwards in the hal file on the firmware line.

Im running the released version of 2.5

Do i need to go to 2.6 pre?

Thanks
Cory
The administrator has disabled public write access.

Re:7i64 & 7i70 - 7i44 - 5i23 support? 06 Lug 2012 17:23 #21663

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1486
  • Thank you received: 40
  • Karma: 89
Sorry - Rename the XML file (you need sudo rights to do that.)

No you need 2.5 but the latest version - the released version is quite behind now.
2.6 pre has most of the fixes just not the very latest (2.5 is not always merged to 2.6 immediately)
So either use git and build from source or use buildbot to download the pre compiled version of 2.5
Unfortunately the buildbot is down right now.

Or just hand edit from this starting point :)
The administrator has disabled public write access.

Re:7i64 & 7i70 - 7i44 - 5i23 support? 06 Lug 2012 21:17 #21667

  • clkeck1
  • clkeck1's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 91
  • Karma: 2
Are there other issues that the newest 2.5 will solve?
If its nothing major I will just hand edit the file.

Thanks
Cory
The administrator has disabled public write access.

Re:7i64 & 7i70 - 7i44 - 5i23 support? 06 Lug 2012 22:52 #21668

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1486
  • Thank you received: 40
  • Karma: 89
There is probably nothing major :
git.linuxcnc.org/gitweb?p=linuxcnc.git;a...fs/heads/v2.5_branch
shows most of them.
The administrator has disabled public write access.
  • Page:
  • 1
  • 2
Moderators: cmorley
Time to create page: 1.611 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.