NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Configuring LinuxCNC StepConf Wizard stepconf woes..

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?
Forum Header

TOPIC: stepconf woes..

stepconf woes.. 21 Mag 2011 20:05 #9982

  • submicro
  • submicro's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 89
  • Karma: 1
Hello

Does anyone running a keling 3 axis kit with kl4030's and c10 breakout board wanna share they're .hal file so I can compare. I'm still unable to get my motors stepping. when in EMC using show hal configuration it shows my x,y,z pins as in not out??? I've tested my parallel port and i have +5v on pins 8 thru 12 but not on the rest.
The administrator has disabled public write access.

Re:stepconf woes.. 22 Mag 2011 00:43 #9983

  • cncbasher
  • cncbasher's Avatar
  • NOW ONLINE
  • Moderator
  • Posts: 761
  • Thank you received: 35
  • Karma: 53
pins voltages are not reliable as an indication , as some pins are bidirectional and therfore give the wrong voltages , the 5volts you are seeing are because the pins are classed as Inputs

can you post your hal file please , also which version of emc and ubunto are you using

Dave
The administrator has disabled public write access.

Re:stepconf woes.. 22 Mag 2011 03:53 #9984

  • BigJohnT
  • BigJohnT's Avatar
  • OFFLINE
  • Administrator
  • Posts: 5082
  • Thank you received: 102
  • Karma: 136
Please read this page to understand the ins and outs of pins.

www.linuxcnc.org/docview/html/hal_basic_hal.html

John
The administrator has disabled public write access.

Re:stepconf woes.. 22 Mag 2011 14:14 #9990

  • submicro
  • submicro's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 89
  • Karma: 1
i'm not sure how to post a file but here goes.... This attachment is hidden for guests. Please log in or register to see it.


i'm using EMC2 2.4.6
linux kernel 2.6.32-122rtai
Attachments:
  • Attachment This attachment is hidden for guests. Please log in or register to see it.
Last Edit: 22 Mag 2011 14:16 by submicro.
The administrator has disabled public write access.

Re:stepconf woes.. 23 Mag 2011 00:27 #9991

  • cncbasher
  • cncbasher's Avatar
  • NOW ONLINE
  • Moderator
  • Posts: 761
  • Thank you received: 35
  • Karma: 53
i'd guess your problem is in the enable , if your using the enable lines to your stepper drivers , remove the wire and you should find it will work
have you connected the enable input ? or using the charge pump
The administrator has disabled public write access.

Re:stepconf woes.. 23 Mag 2011 07:22 #9994

  • submicro
  • submicro's Avatar
  • OFFLINE
  • Expert Boarder
  • Posts: 89
  • Karma: 1
I'm not using the enable lines, and I have the enable on the c10 jumpered. I'm not using a charge pump, I'm not sure what it is.
The administrator has disabled public write access.
Time to create page: 2.107 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.