NEWS
LinuxCNC 2.5.2 Release
There are no translations available.

LinuxCNC 2.5.2 Update Released (changelog).
 
LinuxCNC 2.5.1 Release
There are no translations available.

LinuxCNC 2.5.1 Update Released (changelog). If the Package Manager does not prompt you to upgrade see this page.
 
LinuxCNC 2.5.0 Release
There are no translations available.

New major release (changelog). See the instructions to update your system from EMC 2.4 to LinuxCNC 2.5.
 
Home Forum Configuring LinuxCNC StepConf Wizard 10.04.1 w/ EMC2 - Machine axis config Errno 32

Welcome, Guest
Username: Password: Remember me
Forgot your password? Forgot your username?
Forum Header
  • Page:
  • 1

TOPIC: 10.04.1 w/ EMC2 - Machine axis config Errno 32

10.04.1 w/ EMC2 - Machine axis config Errno 32 09 Sep 2010 16:34 #4080

  • rggrieger
  • rggrieger's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 4
  • Karma: 0
Newly installed 10.04.1 w/ EMC2 on an Asus AMD 64 computer. Used Configuration wizard - Stepper Mill Machine Configuration for x, y, and z axis and they all produced the same error when I ran the test and clicked on any option/setting, e.g.-,

"Stepconf encountered an error. The following information may be useful in troubleshooting:

Traceback (most recent call last):
File "/usr/bin/stepconf", line 1911, in on_jogplus_pressed
self.update_axis_params()
File "/usr/bin/stepconf", line 1900, in update_axis_params
halrun.flush()
IOError: [Errno 32] Broken pipe"

Any suggestions/recommendations on how to fix this problem?

Thks,
Bob
The administrator has disabled public write access.

Re:10.04.1 w/ EMC2 - Machine axis config Errno 32 09 Sep 2010 17:06 #4081

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1486
  • Thank you received: 40
  • Karma: 89
This usually means HAL was already running or there was an error with HAL.
Try running from a terminal. open a terminal and type stepconf.
There will probably be more info in the terminal when the error appears.
Let us know what it says.
The administrator has disabled public write access.

Re:10.04.1 w/ EMC2 - Machine axis config Errno 32 13 Sep 2010 12:53 #4178

  • rggrieger
  • rggrieger's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 4
  • Karma: 0
Running stepconfig by itself corrected the error.

Thanks,
Bob
The administrator has disabled public write access.

Re:10.04.1 w/ EMC2 - Machine axis config Errno 32 09 Oct 2011 09:51 #13790

  • kmonce
  • kmonce's Avatar
  • OFFLINE
  • Fresh Boarder
  • Posts: 1
  • Karma: 0
Hello,

Any additional information regarding this error?

Stepconf encountered an error. The following information may be useful in troubleshooting:

Traceback (most recent call last):
File "/usr/bin/stepconf", line 1914, in update_axis_params
halrun.flush()
IOError: [Errno 32] Broken pipe

I've ran through the step configuration wizard and have it set up according to the instructions. Any ideas how to correct this error?

Let me know if you need additional information.

thanks-KM
The administrator has disabled public write access.

Re:10.04.1 w/ EMC2 - Machine axis config Errno 32 09 Oct 2011 16:32 #13793

  • cmorley
  • cmorley's Avatar
  • OFFLINE
  • Moderator
  • Posts: 1486
  • Thank you received: 40
  • Karma: 89
run stepconf in a terminal.
the terminal will probably give more information.
post the error message.
Also what version of EMC are you using.
The administrator has disabled public write access.
  • Page:
  • 1
Time to create page: 1.398 seconds
Powered by Kunena Forum
© 2013 LinuxCNC.org
Joomla! is Free Software released under the GNU General Public License.